Pages

Friday, September 6, 2013

MIMO Part III

I did the proto-type for the silk scarves on my four shaft Leclerc Fanny.  It's a fairly simple undulating twill that I added a short extended run to for a number of reasons, but the short version is that it worked with my numbers.  :)  

It looked like this:





For one warp of two scarves, I was able to weave it off without mistakes, although it meant un-weaving a number of times as I lost track of where I was in the 20 pick repeat and had to go back to find my place again.  This level of concentration didn't appeal to me over the course of a number of warps, many of them longer than  the two scarf warp I did initially.

In order to make the whole process easier, I decided for a number of reasons to put the warps onto the AVL.

The twenty pick repeat is actually only 16 as the first four and the last four ends are identical.  That meant I could thread the 20 end sequence over 16 shafts as follows:


It took about an hour to transpose the tie up to a 16 shaft lift plan - of course I made a number of mistakes!  What I did was assign a number to the first 16 ends in the 4 shaft version, then checking the tie up on the four shaft version, indicated on the lift plan all the ends that were to behave as though they were on shaft #1 went up when they were supposed to.  Ditto shaft 2, 3, and 4.

When I finally had the liftplan correct there was one more thing I needed to do.  At this point the eight threads on shafts 13-16 were at the back of the loom.  I wanted them at the front - easier to see for one thing!  Using the shaft shuffler tool in Fiberworks, I moved the back four ends to the front four as follows:



In order to do this properly, I set the drawdown for an ordinary treadle tie up, which revealed one more tie up error!  Once everything was cleaned up and the shafts shuffled where I wanted them, I reset the the draft to show the liftplan.

Et voila!

I got the first scarf woven this afternoon and started the next one.  I'm hem stitching on the loom so that when they come off they only need to be wet finished and trimmed.  Hem stitching is actually faster than fringe twisting, and because the warp is silk, it can be left loose.  It might get a little fuzzy, but it won't start to disintegrate like the regenerated cellulose fibres.

I could have done the whole run of scarves on the smaller loom, but it is much faster to weave on the AVL with the auto-cloth advance.  I don't have to stop every two inches to advance the warp.  It is also 'easier' on my neck, not having to keep re-setting the tension.  Since the loom was behaving (mostly), it took just about an hour to weave the first scarf.  

And I can continue putting place mat warps onto the small loom.  Or maybe, just maybe - deal with that rayon chenille!




7 comments:

  1. I just did this for a crackle warp plan that I could also transpose into a damask. I planned it on 4 shafts and transposed it to 20 in a straight threading in runs of 5 threads. Though I did not do it by hand, but used Weavepoint to transpose it automatically. I knew what I'd have to do by hand, but that was quicker.
    Though I'm still designing in the profile on four shafts and will have to transpose for every new design for these towels. Also making samples for a workshop I'll do for the guild in March.
    Teena

    ReplyDelete
  2. Thanks for the original draft - it's so pretty that I wanted to try it. I only have 8 shafts, so I'll have to concentrate on the treadling. Maybe I'll make up a tune and hum it as I weave. Or maybe I'll just have to pay attention (no audio book). Right now, my loom is in transition (as are we) - probably won't be reassembled until January. :-(

    ReplyDelete

  3. /m stuck with 4 shafts, but am going to give it a go.........very pretty.mmIt is a 20mthread pattern and not 16, if I underatand correcty, so the straight threding is repeated between blocks?? Fran

    ReplyDelete


  4. Sorry for the typing errors there> Fran

    ReplyDelete
  5. Follow the four shaft draft exactly and you'll be fine. :)

    cheers,
    Laura

    ReplyDelete
  6. I love all your posts Laura. I learn so much. Thank you

    ReplyDelete

  7. Thanks from me, as well; I read the posts every day, and appreciate all the processes you share.
    Wish me luck with the above draft; the darn treadles are so close together!! Fran

    ReplyDelete